Hanna Instruments (M) Sdn Bhd
11A, Jalan PJS 11/20,
Bandar Sunway,
46150 Petaling Jaya,
Selangor, Malaysia.
+603-5638 9940
Penang Branch Office
Hanna Instruments (M) Sdn Bhd
N0. 303-2-27, Krystal Point,
Jalan Sultan Azlan Shah,
11900 Sungai Nibong,
Penang, Malaysia.
+604-638 4558
+604-645 4558
penang@hannamalaysia.com
Sabah Branch Office
Hanna Instruments (M) Sdn Bhd
No. 4-1, 1st Floor,
Plaza Kingfisher,
Jalan Plaza Kingfisher 5,
Inanam, 88450 Kota Kinabalu,
Sabah, East Malaysia.
088-382 941
088-382 942
sabah@hannamalaysia.com
HI98143 pH and EC Transmitter with Galvanic Isolated Output
| Previous | 13 / 15 | Next |
600 g
In Stock
The HI98143 series is specially designed for long distance measurements of pH and Electrical Conductivity in industrial applications. It can be either panel or wall mounted.
- Four models are available.
- Automatic temperature compensation Connectivity.
- PC compatible.
Direct Connection
- Direct connection of the probes to the transmitter assure a positive electrical connection with no signal loss. This transmitter is ideal for remote process control applications.
Connectivity
- The transmitter can be connected to any pH or conductivity controller, recorder, PC or any data monitoring device that accepts 0 to 1 V, 0 to 4 V or 4 to 20 mA input.
Output Signals
- Four models are available, transmitting a 0-1 V, 0-4 V or 4-20 mA signal. The output signals are proportional to the input signals but independent of changes in load or cable capacitance.
Friendly Design
- Probes connectors, power supply, contacts and calibration trimmers are easy to reach directly on the front panel.
Automatic Temperature Compensation
- Compensation for the effects of temperature for EC measurements are performed by the transmitters’ Automatic Temperature Compenstion circuitry.
Versatile Use
- For in-line applications the recommended pH electrode is the HI1001 while the conductivity probe is the HI3001. HI1001 is a combined double junction pH electrode with BNC and 3m cable; HI3001 is a 4-ring conductivity probe with platinum sensors and an int
pH
| pH Range | 0 to 14 pH |
|---|---|
| pH Accuracy | ±0.5% f.s. pH |
| pH Calibration | manual, 2 point, through trimmers: pH: offset and slope trimmers |
EC/TDS
| EC Range | 0 to 10 mS/cm |
|---|---|
| EC Accuracy | ±2% f.s. EC |
| EC Calibration | manual, 2 point, through trimmers: EC: 0 and 5 mS/cm trimmers |
| EC/TDS Temperature Compensation | automatic, 0 to 60°C (32 to 132°F) with β=2%/°C |
General Meter
| pH Electrode | HI1001 pH electrode (suggested, not included), HI1283 matching pin (not included) |
|---|---|
| EC/TDS Probe | HI3001 (not included) with cell constant 2.1 |
Process Control Meter
| Power Supply | 12-24 VDC |
|---|---|
| Environment | 0 to 50°C (32 to 122°F); RH max 95% non-condensing |
| IP Rating | IP54 |
| Dimensions | 160 x 105 x 31 mm (6.3 x 4.1 x 1.2’’) |
| Weight | 280 g (9.9 oz. |
| Ordering Information | All HI98143 models are supplied with instructions. |